American Dryer Corp. AD-200 Tilting Manuel de l'opérateur

For replacement parts, contact the distributor from which the dryerwas purchased orAmerican Dryer Corporation88 Currant RoadFall River MA 02720-4781Te

6MAXIMUM CAPACITY (Dry Weight) 200 lbs. 90.9 kgTUMBLER (Basket) DIAMETER 62-1/2" 158.75 cmTUMBLER (Basket) DEPTH 42" 106.7 cmTUMBLER (Basket

7B. DIMENSIONS and LOCATIONNOTE: ADC reserves the right to make changes in specifications at any time, without notice orobligation.

8NOTE: ADC reserves the right to make changes in specifications at any time, without notice orobligation.

9NOTE: ADC reserves the right to make changes in specifications at any time, without notice orobligation.

10SECTION IIIINSTALLATION PROCEDURESInstallation in a proper location should be performed by competent technicians in accordance with local andstate c

11NOTE: ADC reserves the right to make changes in specifications at any time, without notice orobligation.1. Reassembly Instructions For Gas Dryer S

12ADG-200 1 Door/2-Way Tilt

13a. Reassembly For 1 Door/2-Way Tilt Gas Dryers;Lift the tumbler (basket) section onto the base.1) 2-Way Tilt dryers have four (4) tilting pistons in

142. Reassembly Instructions For Gas Dryer Shipped In Two PiecesADG-200 1 Door/Forward TiltNOTE: ADC reserves the right to make changes in specificat

15ADG-200 1 Door/Forward Tilt

Retain This Manual In A Safe Place For Future ReferenceAmerican Dryer Corporation products embody advanced concepts in engineering, design, and safety

16a. Reassembly For 1 Door/Forward Tilt Gas Dryers;Lift the tumbler (basket) section onto the base.1) Forward Tilt dryers have two (2) tilting pistons

173. Reassembly Instructions For Gas Dryer Shipped In Two PiecesADG-200 2 Door/Rear Tilt(Pass Thru)NOTE: ADC reserves the right to make changes in s

18ADG-200 2 Door/Rear Tilt(Pass Thru)

19a. Reassembly For 2 Door/Rear Tilt (Pass Thru) Gas Dryers;Lift the tumbler (basket) section onto the base.1) Rear Tilt dryers have two (2) tilting p

20NOTE: ADC reserves the right to make changes in specifications at any time, without notice orobligation.4. Reassembly Instructions For Steam Dryer

21ADS-200 1 Door/2-Way Tilt

22a. Reassembly For 1 Door/2-Way Tilt Steam Dryers;Lift the tumbler (basket) section onto the base.1) 2-Way Tilt dryers have four (4) tilting pistons

235. Reassembly Instructions For Steam Dryer Shipped In Two PiecesADS-200 1 Door/Forward TiltNOTE: ADC reserves the right to make changes in specifi

24ADS-200 1 Door/Forward Tilt

25a. Reassembly For 1 Door/Forward Tilt Steam Dryers;Lift the tumbler (basket) section onto the base.1) Forward Tilt dryers have two (2) tilting pisto

IMPORTANTYOU MUST DISCONNECT and LOCKOUT THE ELECTRIC SUPPLY and THE GASSUPPLY or THE STEAM SUPPLY BEFORE ANY COVERS or GUARDS AREREMOVED FROM THE MAC

26NOTE: ADC reserves the right to make changes in specifications at any time, without notice orobligation.6. Reassembly Instructions For Steam Dryer

27ADS-200 2 Door/Rear Tilt(Pass Thru)

28a. Reassembly For 1 Door/Forward Tilt Steam Dryers;Lift the tumbler (basket) section onto the base.1) Rear Tilt dryers have two (2) tilting pistons

29B. LOCATION REQUIREMENTSThe model AD-200 tilting dryer requires 18-inches (45.72 cm) on the right side of the dryer for ease ofmaintenance. For th

30C. FRESH AIR SUPPLY REQUIREMENTSWhen the dryer is operating, it draws in room air, heats it, passes this air through the tumbler (basket), andexhau

31D. EXHAUST REQUIREMENTSNOTE: For 1 Door ADG-200 dryer models, the 20-inch (50.8 cm) diameter exhaust duct exitsfrom the rear of the base. For 2 Do

32ALL duct work should be smooth inside with no projections from sheet metal screws or other obstructionswhich will collect lint. When adding ducts,

332. Single Dryer VentingWhere possible, it is suggested to provide a separate exhaust duct for each dryer. The exhaust duct shouldbe laid out in suc

34IMPORTANT: For extended duct work runs, the cross section area of the duct work can only beincreased to an extent. Maximum proportional duct work r

35The main duct may be any shape so long as the minimum cross section area is provided. The illustration onpage 36 shows the minimum cross section ar

WARNINGThe dryer must never be operated with any of the back guards, outer tops, or servicepanels removed. PERSONAL INJURY or FIRE COULD RESULT.IMPOR

36

37E. COMPRESSED AIR SUPPLY SYSTEMThe compressed air system of the AD-200 Tilting dryer consists of a number of pneumatic pistons locatedthroughout th

383. Internal/External Pilot Air SupplyOn 2-Way-Tilt dryers, a pneumatic safety circuit is incorporated to prevent both front and rear tilting pistons

39F. ELECTRICAL INFORMATION1. Electrical RequirementsIt is your responsibility to have ALL electrical connections made by a properly licensed and com

402. Electrical Service SpecificationsIMPORTANT: The dryer must be connected to the electric supply shown on the data label thatis affixed to the back

41ADS-200 with Tilting Options15 HP Blower / 3 HP Drive MotorIMPORTANT: 208 VAC AND 230 VAC ARE NOT THE SAME. When ordering, specify exact voltage.

423. Electrical ConnectionsNOTE: A wiring diagram is included with each dryer and is located in the blueprint pocketinside the left side control cabin

43G. GAS INFORMATIONIt is your responsibility to have ALL plumbing connections made by a qualified professional to assure that thegas plumbing instal

442. Technical Gas Dataa. Gas Specificationsb. Gas Connections:Run a 1-1/2” (3.81 cm) pipe from the main gas header to the dryer. There is a 1-1/2” (

453. Piping/ConnectionsALL components/materials must conform to National Fuel Gas Code specifications. It is important thatgas pressure regulators me

Table of ContentsSECTION IIMPORTANT INFORMATION ...

46Consistent gas pressure is essential at ALL gas connections. It is recommended that a 2-inch (5.08 cm) pipegas loop be installed in the supply line

47H. STEAM INFORMATIONIt is your responsibility to have ALL plumbing connections made by a qualified professional to assure that thegas plumbing ins

48d. Shut-off valves for each dryer should be installed in the supply line, return line, and drip trap returnlines. This will allow the dryer to be i

493. Steam Damper Air System ConnectionsThe ADS-200 is manufactured with a pneumatic (piston) damper system which requires an external supplyof compre

504. Steam Damper System OperationThe ADS-200 steam damper in the Heating Mode as shown in Diagram 1, allows the coil to stay constantlycharged elimin

51I. STEAM DAMPER ACTUATOR SYSTEMThe system consists of a hinged damper plate, pneumatic piston, and a 24 volt solenoid valve with a needle valveto c

52K. PREOPERATIONAL TESTSALL dryers are thoroughly tested and inspected before leaving the factory. However, a preoperational testshould be preforme

53NOTE: Dryer can be stopped at any time by opening the main door or by pressing the “CLEAR/STOP” key. To restart the dryer, press the “ENTER/START”

542) Make a complete operational check of ALL safety-related circuits (i.e., lint drawer switch and sailswitches on Gas Models).3) A reversing tumbler

5510. Check bolts, nuts, screws, terminals, and fittings for security.11. Check to insure air supply (80 PSI [5.51 bars]) is connected to the dryer.12

SECTION VIICOMPONENT SYSTEM DESCRIPTIONS... 62A. TUMBLER DRIVE SYSTEM

56SECTION IVSERVICE/PARTS INFORMATIONA. SERVICE1. Service must be performed by a qualified trained technician, service agency, or gas supplier. If s

57SECTION VWARRANTY INFORMATIONA. RETURNING WARRANTY CARD(S)1. Before any dryer leaves the ADC factory test area, a warranty card is placed on the ba

582. Each part must be tagged with the following information:a. Model number and serial number of the dryer from which the part was removed.b. Nature

59SECTION VIROUTINE MAINTENANCEA. CLEANINGA program and/or schedule should be established for periodic inspection, cleaning, and removal of lint from

60MONTHLYEmpty the compressed air filter bowl.EVERY THREE MONTHSRe-grease the two (2) 1-3/8-inch (3.5 cm) bearings that support the impellor/fan shaft

61B. ADJUSTMENTS7 DAYS AFTER INSTALLATION and EVERY 6 MONTHS THEREAFTERInspect bolts, nuts, screws (bearing set screws), non-permanent gas connection

62SECTION VIICOMPONENT SYSTEM DESCRIPTIONSA. TUMBLER DRIVE SYSTEMThe tumbler (basket) is supported and driven by four (4) 11-inch (27.94 cm) diameter

63B. TUMBLERThe tumbler (basket) is made of 14-gauge stainless steel perforated panels, four (4) stainless steel ribs, and two(2) outer tumbler rings

644. Burner Box Hi-Limit Safety Thermostats (for Gas Dryers ONLY)These disk temperature switches have a setting of 330º F (166º C). They are located

65E. STEAM DAMPER ACTUATOR SYSTEMThe system consists of a hinged damper plate, pneumatic piston, and a 24 volt solenoid valve with a needle valveto c

3SECTION IIMPORTANT INFORMATIONA. RECEIVING and HANDLINGThe dryer is shipped in a protective stretch wrap cover with protective cardboard corners as

ADC 113109 1- 02/09/00-25 2- 05/26/00-20 3* 01/02/01-10

4B. SAFETY PRECAUTIONSWARNING: For your safety, the information in this manual must be followed to minimize therisk of fire or explosion or to preve

5WARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber, orsimilarly textured rubber materials. Drying in a heated tu