American Dryer Corp. ADG / MLG-170DR Manuel d'installation

ADG / MLG-170DRInstallation ManualPhase 7 / Non-Coin / DSI / Dual Timer / Fire Suppression SystemADC Part No. 113409-2AVERTISSEMENT: Assurez-vous de b

10 American Dryer Corp. 113409-22. If more headroom is needed when moving the dryer into position, the top console (module) may be removed.a. To Remov

113409-2 www.amdry.com 11C. DRYER ENCLOSURE REQUIREMENTSBulkheads and partitions should be made of noncombustible material.NOTE: Allowances must be m

12 American Dryer Corp. 113409-2D. FRESH AIR SUPPLY REQUIREMENTSWhen the dryer is operating, it draws in room air, heats it, passes this air through

113409-2 www.amdry.com 13E. EXHAUST REQUIREMENTS1. General Exhaust Ductwork InformationExhaust ductwork should be designed and installed by a qualifi

14 American Dryer Corp. 113409-2NOTE: As per the National Fuel Gas Code, “Exhaust ducts for Type 2 clothes dryers shall be constructed ofsheet metal o

113409-2 www.amdry.com 15IMPORTANT: Exhaust back pressure measured by a manometer at each tumbler exhaust duct area must beno less than 0 and must not

16 American Dryer Corp. 113409-2NOTE: When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible materials, theopening must

113409-2 www.amdry.com 17The ductwork should be smooth inside with no projections from sheet metal screws or other obstructions, whichwill collect lin

18 American Dryer Corp. 113409-2MULTIPLE DRYER VENTING (GAS DR MODELS)WITH 12” (30.48 CM) DIAMETER (3,700 CFM [104.77 CMM]) CONNECTIONS AT COMMON DUCT

113409-2 www.amdry.com 19F. ELECTRICAL INFORMATION1. Electrical RequirementsALL electrical connections must be made by a properly licensed and compet

“IMPORTANT NOTE TO PURCHASER”Information must be obtained from your local gas supplier on theinstructions to be followed if the user smells gas. Thes

20 American Dryer Corp. 113409-22. Electrical Service Specificationsa. Gas Models OnlyGasELECTRICAL SERVICE SPECIFICATIONS (PER DRYER) IMPORTANT:

113409-2 www.amdry.com 213. GroundingA ground (earth) connection must be provided and installed in accordance with state and local codes. In theabsen

22 American Dryer Corp. 113409-2G. GAS INFORMATIONIt is your responsibility to have ALL plumbing connections made by a qualified professional to ensu

113409-2 www.amdry.com 232. Technical Dataa. Gas SpecificationsShaded areas are stated in metric equivalents* Measured at the gas valve pressure tap w

24 American Dryer Corp. 113409-2

113409-2 www.amdry.com 25H. WATER INFORMATIONBEFORE YOU START!CHECK LOCAL CODES AND PERMITSCall your local water company or the proper municipal auth

26 American Dryer Corp. 113409-2OPTIONAL MANUAL BYPASSProvisions are made in the dryer’s fire suppression system for the installation of an optional m

113409-2 www.amdry.com 2711. Check bolts, nuts, screws, terminals, and fittings for security.12. Check to ensure air supply (80 psi [5.51 bar]) is con

28 American Dryer Corp. 113409-2IMPORTANT: There is no regulator provided in an L.P. dryer. The water column (W.C.) pressure must beregulated at the

113409-2 www.amdry.com 29The L.E.D. display will read MANUAL DRYING CYCLE D, 00:00 MIN REMAIN.NOTE: The dryer can be stopped at any time by pressing t

IMPORTANTYou must disconnect and lockout the electric supplyand the gas supply or the steam supply before anycovers or guards are removed from the mac

30 American Dryer Corp. 113409-2M. SHUTDOWN INSTRUCTIONSIf the dryer is to be shutdown (taken out of service) for a period of time, the following mus

113409-2 www.amdry.com 31SECTION IVSERVICE/PARTS INFORMATIONA. SERVICE1. Service must be performed by a qualified trained technician, service agency,

32 American Dryer Corp. 113409-2SECTION VWARRANTY INFORMATIONA. RETURNING WARRANTY CARDSBefore any dryer leaves the ADC factory test area, a warranty

113409-2 www.amdry.com 332. Each part must be tagged with the following information:a.Model number and serial number of the dryer from which part was

34 American Dryer Corp. 113409-2SECTION VIROUTINE MAINTENANCEA. CLEANINGA program and/or schedule should be established for periodic inspection, clea

113409-2 www.amdry.com 356 MONTHSInspect and remove lint accumulation in customer furnished exhaust ductwork system and from dryer’s internal exhaustd

36 American Dryer Corp. 113409-2SECTION VIIMANUAL RESET BURNER HI-LIMIT INSTRUCTIONSA. PHASE 7This dryer was manufactured with a manual reset burner

113409-2 www.amdry.com 37SECTION VIIIDATA LABEL INFORMATIONWhen contacting ADC, certain information is required to ensure proper service/parts informa

38 American Dryer Corp. 113409-2SECTION IXPROCEDURE FOR FUNCTIONAL CHECKOF REPLACEMENT COMPONENTS1. Microprocessor Controller (Computer) Boarda. Upon

113409-2 www.amdry.com 392. For Models with Direct Spark Ignition (DSI) Module (Type I)Theory of Operation:Start the drying cycle. When the gas burne

4 American Dryer Corp. 113409-2SECTION ISAFETY PRECAUTIONSWARNING: For your safety, the information in this manual must be followed to minimize the ri

ADC Part No. 113409 2 - 06/12/08 - 1

113409-2 www.amdry.com 5WARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber, or similarlytextured rubberlike materi

6 American Dryer Corp. 113409-2SECTION IISPECIFICATIONSShaded areas are stated in metric equivalents 03/25/05IMPORTANT: Gas dryers must be provided wi

113409-2 www.amdry.com 7NOTE: ADC reserves the right to make changes in specifications at any time without notice or obligation.Specifications – Gas

8 American Dryer Corp. 113409-2SECTION IIIINSTALLATION PROCEDURESInstallation should be performed by competent technicians in accordance with local an

113409-2 www.amdry.com 9IMPORTANT: The dryer must be installed in a location/environment, which the ambient temperatureremains between 40° F (4.44° C)